Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - trev

#61
Hi, my RV4s sounds like the stepper motor that rotates the pickup is missing steps. Video link attached.

https://youtu.be/_QtO8nigj3A

It feels like a harness issue to me. I replaced the stepper motor and it made no difference so it's not the stepper motor. I replaced the connector in the stepper motor head and soldered the wires together. This made no difference. The issue is intermittent as well which makes me feel like its a wiring issue. I am just wondering if anyone has had this fault and can confirm what they did to fix it? My thought is to replace the harness that goes from the stepper motor to the arm body where the circuit board is mounted.

https://youtu.be/_QtO8nigj3A

Thanks

Trev
#62
In case anyone is looking for a wireless keyboard and mousepad, I bought a LOGITECH K400 Plus despite it not stating win98 support and it appears the mouse pad and keyboard both work with Win98 without the need for any special Logitech drivers.
#63
RV Hardware / Re: Feeder controller board redesign
January 18, 2022, 09:28:18 PM
Side view of a feeder in action using my new board. It also shows the mechanism for anyone who hasn't opened a feeder.

https://youtu.be/JyTG3TL-eME
#64
RV Hardware / Re: Feeder controller board redesign
January 12, 2022, 09:45:29 PM
Been a while since I did work on this. All my attention up until today had been with a grey feeder where the positioning pin is right at the front of the feeder. I was still finding that despite motion being good everything else was rubbish. I just could not get reliable movement and was feeling beaten. The tape would lift up sometimes and the pin not move it. With too little tension on the pin the tap would still bounce about. I was a bit gutted after all the work I had done. I felt it was never going to work. It was working perfectly for SOT23 and thicker tape but 0603 LEDs was still bad.

Today though I found the motivation to try again but with a blue feeder. These feeders have the positioning pin at the middle of the feeder right next to the rubber band. This seems to have made a massive difference. With the super smooth motion my board created there is no vibration of leds when the tape is moved. The stepper motor gearing does not chatter at all. But what's different is the positioning pin  is so far from the open end of the tape that it does not affect the leds at all when it snaps up and down. So the original issue with blue feeders I think was mainly the movement rather than the action of the pin going up and down. With the grey feeders the issue is that movement and also the pin being so close to the open end of the tape that it caused vibration when snapping up and down.

I placed 350 leds today and had no pickup failures. It was perfect. Will keep using it but it is looking very positive finally.

Have attached link to led movement in action. It is super smooth every time which I also think helps reduce band slippage and also reduces the risk of the pin stretching the hole in the plastic tape and causing movement failure. 

https://youtu.be/0Wu516kW94U

Trev
#65
RV Hardware / Re: 0402 placement tips
January 12, 2022, 09:21:26 PM
I did a test board to see what placement I could get with an RV4s for 0402 resistors. It was quite impressive, I was surprised.

I used some spray mount and attached image shows the position accuracy. This was full speed as well.
#66
Thanks, will try your sequence and see if that solves it.
#67
Hi, most of the time when I load up RV Place the camera has some weird offset. A black band appears at the bottom. I believe this is related to the PC and wondering if it is a hardware or software issue. Maybe I installed the wrong camera driver? Has anyone experienced this issue?

I have attached an image showing the black band at the bottom. It does affect the position of placement.

Trev
#68
RV Hardware / Re: Feeder controller board redesign
September 23, 2021, 10:29:18 PM
I did a run of a few boards today and compared using a feeder with an old control board in it with one with my new design. I have to say, the old feeder is so fast. I am not sure why they felt the need to move the tape so quickly though. They have so much time between placements! Maybe when using merge moves or something and the feeder is right next to the camera, it needs to be. The speed can not help when winding the tape back though. I much prefer my new design.

I am going to build a few more boards up and convert some more feeders. I then have a big job to get done and this should really put the board through final testing.

Trev


#69
RV Hardware / Re: Feeder controller board redesign
September 22, 2021, 01:53:03 PM
I have now done around 2000 placements with a feeder installed with the new controller design. It has not missed a beat and appears to be performing very very nicely. Lovely smooth movement means the components are always in the same position and I think this helps placement be that little bit more repeatable. Also being so quiet is fantastic.

I was not using lots of plastic tape due to the job I had to get done. It was mainly paper but there were 2 plastic tapes on the bank. They were quite thick, the one held a SOT23-5 and the other a 1210 inductor. The SOT23-5 moved very smoothly with not shaking in the tape. Position again was very repeatable.

What I did find out though is the reduced voltage for solenoid operation is because I did not fit the extra springs on the grey feeder. This style feeder has 2 sets of springs to help stop the pins sticking and I did experience a bit of pin sticking. When I checked a different feeder I found the solenoid voltage needed to be up at around 24V to work reliably due to the extra force of the springs. Still seems that 37-39V is quite high.

The other thing is that with higher voltage the solenoid does not like to be energised for long. With the original design moving the tape quickly, the solenoid was on for less time and this may have helped keep heat down. We this design design if the voltage is less this might balance out.

I have another mod to try to stop the pin hitting the plate that does not require any machining of the pins. If this works then I think I will have a final solution.

Finally I have attached a pic of the first hand soldered controller board built from PCBs I got made. Everything appears to be working as expected.


#70
RV Hardware / Re: Feeder controller board redesign
September 13, 2021, 11:51:22 AM
This panel mount one looks interesting. It could be installed inside the RV power enclosure and then feed the cable so no external cable alterations would be required. Then you can adjust the voltage from the panel. Nice and tidy.

https://www.amazon.co.uk/Voltage-Regulator-Programmable-Adjustable-Converter/dp/B08P7PG7R5/ref=sr_1_37?dchild=1&keywords=adjustable+power+supply&qid=1631530107&s=electronics&sr=1-37

Anyone know if these blow up a lot?
#72
RV Hardware / Re: Feeder controller board redesign
September 13, 2021, 11:43:08 AM
The solenoid seems to move pretty quick, maybe 10s of ms. I read up a bit and you need that kick to get the thing moving. Once it has moved into position you can reduce the current/voltage to hold it in position but the initial movement needs to be good. I do not know how much variation there is between a cold day and a warm day. Or even from solenoid to solenoid production variation.

Maybe the original pins do not need to be machined if the voltage level is set correctly. I am hoping, once the PCBs arrive I can build one up with the secondaries connected in parallel. I think it really only needs one secondary connected now as the current consumption is greatly reduced. Probably I can wire across the one bridge rectifier and test it out. Might be as simple as that. But if the pins do need to be changed that is not the end of the world. It would certainly make replacing the controller board a lot easier if the pins did not need changing. 

But if I also need to use a bench supply and program the voltage to just be on the edge each time, that is not the end of the world for me. I mean 18V-20V at 400mA is nothing really. All the feeders could be powered from a basic bench supply very easily. The transformers could be completely removed. The big cap on the board would help with solenoid current draw but everything else I reckon would be pretty stable. I do not think there would be much voltage drop in the cables powering the feeders from a supply. 

This would be totally over the top but be able to serve all the feeders connected and is pretty cheap really.

https://cpc.farnell.com/tenma/72-10480/power-supply-1ch-30v-3a-adjustable/dp/IN06822?st=bench%20power%20supply

Trev
#73
RV Hardware / Re: Feeder controller board redesign
September 12, 2021, 12:13:08 PM
I assembled the feeder and ran into issues with the pin action creating massive vibration when it hit the plate. With the current setup I measure a voltage of 39V on the solenoid pins under no load which seems too high. I had previously seen around 37V. It depends on the load the transformer is under but it seems very high.

I stripped the whole feeder down again to see what I could do. After a lot of tinkering I felt the pin was hitting the plate very hard so I decided to take a bit of the shoulder off the pin. You can see the before and after in the images attached.

The sound before I did this mod was a hard metal hitting metal sound. I think it was a very sharp impact which was causing the leds to bounce out of the tape or flip upside down. The sound now is more of a thud from the metal plate that moves the pin hitting the base of the solenoid. It seemed still though to be very hard and I could see 0603 leds still bounce a bit. It was better but not ideal.

So next I changed the solenoid voltage. I connected my bench power supply and found that the solenoid moves from as low as 15V. I know at 39V the solenoid gets really hot  if you are doing repeated operations. I settled the PSU on approx. 19V and this seems to have good pin movement but reduces the energy of the pin movement impact. I settled on 19V because this is the voltage created when the mains transformer is wired in parallel instead of in series. I am not sure if over time the solenoids need more voltage to move pins. Maybe dirt build up makes the pin harder to move. Maybe temperature has an impact. I do not know but I am convinced at present 39V is just too high.

I have some boards to make which will enable me to test the feeder with several thousand component placements so I think this will provide me with good data. For now this latest video shows decent feed of 0603 leds with approx. 19V powering the solenoid and the stepper. I also tweaked the speed and acceleration/deceleration profile.

https://youtu.be/xdlcmy4m140

#74
RV Hardware / Re: Feeder controller board redesign
September 07, 2021, 11:34:16 PM
For those interested in the USB version, the USB adapter fits perfectly where the dip switch board went without any case modification.

I do not see an issue to have dual interface. People can leave the dip switches in place and fit the USB elsewhere if they want.

So if you plug the USB in you can connect via a terminal application and configure the system. If you flip SW8 then you can also program via indexing method Mike suggested. Terminal interface will display all settings by pressing enter.

#75
RV Hardware / Re: 0402 placement tips
September 07, 2021, 09:45:20 AM
Thanks