Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Mike

Pages: [1] 2 3 ... 39
1
RV Hardware / Re: Moving RV
« on: August 10, 2020, 10:47:15 PM »
Yes, remove feeders, unplug the connectors from the bottom rear, and the arm/table unit just lifts off.

2
RV Hardware / Re: OTF & ghost pictures
« on: July 22, 2020, 08:28:42 PM »
Might help if you could post pics of what you are seeing.
Also, if you set the cam threshold way off, so it sees no features,
 think it shows the greyscale video image-this may be helpful in identifying issues. Could be a wierd issue with the capture card, or maybe a video ground off, so noise from somewhere is causing interference.
A regular issue is the IDC 0.1" headers used in various places-may be worth replacing the ones on the arm board with crimped or soldered ones like JST or Molex. Maybe also put a scope on the camera power to see if there's any noise or glitches.
I thing the video signal passes through a relay on the arm board to switch between otf and fixed cams. If monitoring the video, ty to do it at the input of the capture card

3
RV Hardware / Re: OTF & ghost pictures
« on: July 22, 2020, 12:42:56 PM »
Regulator is on the PCB on the side of the arm.

4
RV Hardware / Re: OTF & ghost pictures
« on: July 21, 2020, 12:29:06 AM »
If it's stray pixels etc. Try tweaking the camera threshold. Also check for marks, paste etc. On the lower face of the nozzle

5
RV Hardware / Re: OTF & ghost pictures
« on: July 21, 2020, 12:27:06 AM »
I've seen an issue that looks like it's getting the fields of the interlaced video frame the wrong way round or similar-a comb-like appearance on edges. I think it can happen if the video signal disappears, e.g. bad video or camera power connection.  Once it starts, it happens consistently until power on everything is cycled
I think I saw it when I powered up the RV box before the PC. Haven't seen it since I made a habit of allowing the pc to boot before turning the machine power on

6
AIUI the X/Y aspects of these functions are basically equivalent. Setup just sets the initial values so the fid cam starts in roughly the right place

7
RV Hardware / Re: video capture card
« on: January 24, 2020, 10:10:48 AM »
Saved searches on ebay are handy when looking for very specific things like this. I got my spare capture card at a good price after a few months

8
RV Software / Re: Calibration
« on: January 17, 2020, 12:26:15 PM »
RV camera cal info from alanambrose - added here to keep cal info together

9
RV Hardware / Re: detailed camera(s) calibration procedure
« on: December 29, 2019, 12:17:42 PM »
This thread has the current collective state of knowledge on calibration:

http://electricstuff.co.uk/forum/index.php?PHPSESSID=jj4de78ol8la24pteh9g6q1827&topic=313.0


10
RV Software / Re: Tips for accurate placement?
« on: November 21, 2019, 11:11:13 PM »
Centring of the feeder pick location isn't a huge deal as unless feeders are locked in the CDF, it will tweak the pick position over multiple picks until it's centred.  This can be an issue if the vision isn't set up optimally, such that the centre position isn't very consistent. Inductors with solder on the bottom are a regular problem.
Locking feeders can be helpful in some cases, but the first thing to do is optimise the vision thresholds and blob size.   

11
RV Software / Re: Weird mouse behaviour
« on: November 13, 2019, 02:25:05 PM »
I've seen this a few times, I think it was a stuck button on the gamepad, or the gamepad getting into an odd state that was fixed by unplugging & replugging it.

12
For Sale/Wanted, Suppliers / Re: FS RV1S - £100 Loughton Essex.
« on: October 28, 2019, 06:46:20 PM »
Gone.

13
For Sale/Wanted, Suppliers / FS RV1S - £100 Loughton Essex.
« on: October 21, 2019, 11:14:04 AM »
Part of a lot I picked up a while ago - RV1S base unit only with PSU box and PC. No frame,feeders,nozzles or PCB holders. I did have it running a while ago but it's just been sitting gathering dust since.
I have an RV4s so not likely to be very useful for parts & now want to clear the space, and I can't be arsed to set it up again to demo to a potential buyer, so prefer to go to someone already familiar with the machines as a spare. 
Collection only Loughton Essex

14
RV Hardware / Re: Anyone want any brass inserts for nozzles?
« on: August 30, 2019, 02:02:37 PM »
I'll take 10 - let me know how you want payment

15
RV Software / Re: Repeatable placement issues
« on: August 04, 2019, 09:45:55 AM »
By "screen corruption" do you mean the well-known thing where the screen display becomes offset, or something else?

Incidentally the quickest way to recover the former is to load any other job, ignore the feeder error messages, then reload the job you were doing. This avoids the re-homing delay when starting RVPlace

Pages: [1] 2 3 ... 39